PC Case - Pre-Installed 6 PWM ARGB Fan, ATX Mid-Tower Gaming PC Case,Type-C, FOIFKIN (Black, F1)

I. Love. This. Case!It fits my esthetic, and it's so chic- my ONLY complaint was that the directions were a pain in butt to find! They were taped into the bottom PSU slot and so we struggled for way too long to figure out what pieces came off and all that- this is my first build. It came with zip ties for cable management, and very easy to read instructions (after we found them), it is sturdy and well made, and the air flow is great!

PRO:Very nice looking case! The gap between the motherboard tray and the backside of the case is big enough to hide wiring pretty easily, the pre-installed fans are quiet and have LED lighting that syncs with other components. If you go liquid cooling, it'd be pretty easy to install a 360mm radiator on the top.CON:I feel like I'm about to break the glass sometimes when I try to remove it, since it is held in place by a couple plastic clips and it takes some force to pop it out. Also, the preinstalled fans on the bottom crowd the bottom side of the motherboard, where you usually find front panel connectors for usb, audio, etc. I found I needed to connect those before installing the motherboard in order to get everything in place.

Very pleased with customer service. Case arrived damaged by carrier. The replacement process was easy and painless. Case itself is good quality especially for the price. I am very happy with my choice and purchase.

Four star only because theres a major flaw in my honest opinion. The USB header plug that comes with the case sticks out pretty far. So if you have an ATX motherboard the bottom fans block the connection for the plug. To keep the bottom three fans you must also purchase a 90 degree 19 pin usb adapter. Its not expensive its an extra $6-10. So either buy an adapter, run a MATX mobo, OR dont run the fan on the bottom middle section as I was for a few days. Other than that, its a pretty nice case. I also wish the wires that come with the case fans where longer. Not easy to organize these wires when there barely 2 inches apart from each other.

Good case for the price!This case has lots of room to install stuff, for the price it’s a great value. My only complaint with it would be that the top doesn’t come off, so it is a bit harder to install and remove the AIO, but other than that, it’s a good buy!This case is honestly underrated, it’s really hard to find a good case for under $150 and this one is hard to pass up.

I've built a lot of PCs and this is a good option to consider if you are interested in the aquarium look. I am giving a 5 star for a 4 star case with a +1 star for value.During installation you may need to remove one or two of the bottom intake fans during installation of the board and connection of I/O and fans headers. Maybe somebody with small fingers wouldn't need to, but removing the fans was quick and easy and once they weren't in the way you have full access to the edges of the motherboard. All six of the included fans work great. You may want to add an additional magnetic mesh screen for the side intake. You could move the top mesh to cover the side intake (since the top is typically an exhaust), but doing so makes the top look ugly. So spring an extra $5-8 for a black mesh on the side.If you plan on using the drive cage in the lower section it may make power supply sizing a challenge. I removed it so it didn't matter to me, but if you want to use it you should get as short a power supply as possible and expect some annoyance squeezing the cables around it. There is plenty of room for routing cables all around the motherboard. The top fits a 360 or even a 280 radiator, which is nice. The default ARGB colors of the single 120mm exhaust fan are slightly different from the five intake fans, but once you apply any ARGB control they unify just fine.An unexpected plus, while the PCI covers on the case are snap-off they did include a couple traditional screw-on covers to replace some if you change your mind after an installation in the future.The only real negative is that while it does have a USB-C plug on top that port is sharing a USB3 plug on the motherboard and does not utilize the high bandwidth USB-C connection that some boards have. I think that was the only real negative that wasn't very easily accounted for. I don't need high speed USB-C connectivity on the top, but if you do need it that will be a problem. I'm not attaching a pic because it looks the same as pictured.

Absolutely amazing. Well built, nice fans! Easy to work with.

Came very dented and nothing would fit or stay on. Very disappointed